Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Presented here below you can find more excellent data all about How to Install a Bathtub Yourself.
Setting up a tub isn't specifically brain surgery, but it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified on your own for the work as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you may need a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the producer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also inspect the overflow outlet as well as the typical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub should wait until the bathtub has been used at least once as this will resolve it right into its last placement.
Planning for the Setup
First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in issues with dampness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes and cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can break rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been guided to that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from someone on another domain. Do you know another individual who is in to the subject? Be sure promote it. I praise you for your time. Visit us again soon.
Instant Quote Report this page